Almost every rider who has struggled up a loaded climb has been told they need lower gears, and almost none have been told how to work out what that means. Bike shops talk in tooth counts, catalogues talk in percentages, and old touring manuals talk in gear inches. None of those numbers are wrong, but they hide the only thing that matters: how far the bike moves per pedal revolution, and whether you can keep a sensible cadence when the road tilts up and the bags are full. This is our attempt to make gearing arithmetic plain, then apply it to the climbs we actually ride.
The one number to understand: gear ratio
A gear ratio is the number of teeth on the chainring divided by the number of teeth on the rear sprocket. A 32-tooth chainring driving a 32-tooth sprocket gives a ratio of 1.0: one turn of the cranks turns the wheel once. A 40 ring with a 10 sprocket gives 4.0, so the wheel turns four times per pedal stroke. That is the whole idea. Everything else is a unit conversion.
To get distance per revolution, multiply the ratio by the wheel circumference. A 29 inch wheel with a 2.2 inch tyre has a circumference of about 2.3 m, so a 1.0 ratio moves the bike 2.3 m per crank turn, and a 4.0 ratio moves it 9.2 m. Gear inches, the old unit, is the ratio multiplied by the wheel diameter in inches, so that same 1.0 ratio on a 29 inch wheel is about 29 gear inches, and 4.0 is about 116. On that scale, 20 is a very low gear and 100 a fast one.
Cadence, speed and why the climb sets the gear
Most of us pedal comfortably between 70 and 90 revolutions per minute on the flat, and can hold 60 on a climb for a long time. Below about 50, the muscles are working like a weightlifter rather than an endurance athlete, and knees start to complain. So the question for any gear is simple: at 60 rpm, how fast does it move the bike, and can we climb the hill at that speed?
Take a 1.0 ratio on the 29 inch wheel. At 60 rpm that is 60 turns of 2.3 m, or 138 m per minute, which is 8.3 km/h. On a 10 percent gradient with a system weight of 100 kg, holding 8.3 km/h requires roughly 230 watts against gravity alone, a hard effort for most riders and unsustainable for a day. Drop to a 0.8 ratio and the same 60 rpm gives 6.6 km/h and about 180 watts. Drop to 0.7 and it is 5.8 km/h and 160 watts, which many fit riders can hold for an hour on a loaded bike. Below about 5 km/h balance becomes the limit rather than the legs, so gears lower than roughly 0.6 have diminishing returns unless the surface is very rough.
How low is low enough
Our rule, arrived at the hard way, is that a loaded touring or bikepacking bike wants a lowest gear between 0.6 and 0.8, with 0.7 as the sweet spot for real mountain routes. On a 29 inch wheel that is roughly 18 to 24 gear inches. Here is how various common setups land on that scale.
- Single 40 ring with a 10-42 cassette: lowest ratio 0.95. Fine for fast gravel, brutal loaded above 8 percent.
- Single 38 ring with a 10-46 cassette: lowest 0.83. Workable for light loads and rolling terrain.
- Single 32 ring with a 10-51 cassette: lowest 0.63. Comfortable for full loads on long steep climbs; top gear of 3.2 is enough for 40 km/h on the flat.
- Double 46-30 with an 11-34 cassette: lowest 0.88. The typical off-the-shelf gravel double, and the one most people find too tall once loaded.
- Double 42-26 with an 11-40: lowest 0.65. An excellent touring range with a real top end.
- Triple 44-32-22 with an 11-36: lowest 0.61. The classic touring answer, and still hard to beat for range.
The single-ring setups pay for their simplicity with large gaps between gears: a 10-51 cassette jumps 15 to 20 percent between sprockets, which is noticeable on rolling roads. Doubles and triples give closer steps at the cost of a front derailleur to maintain.
Range versus spacing
Range is the ratio between the highest and lowest gear, usually quoted as a percentage. A 10-51 cassette is 510 percent; a 46-30 double with 11-34 is about 470 percent. Most people fixate on range, but for touring we care nearly as much about where the range is placed. A rider who never exceeds 35 km/h on a loaded bike does not need a 4.0 top gear; anything above about 3.2 is coasting territory anyway. Every tooth removed from the top end can be moved to the bottom, which is the logic behind fitting a smaller chainring to a stock bike.
Changing the chainring on a single-ring bike from 40 to 34 lowers every gear by 15 percent. On a double, swapping the inner ring from 30 to 28 or 26 lowers the climbing gears only, which is usually what we want. Check derailleur capacity and the minimum ring size the crank accepts first.
Reading a route with these numbers
Elevation profiles come with every route file, so we plan the gearing before the trip. A route that averages 5 percent on its climbs with short ramps to 10 percent is fine with a 0.8 low gear. A route with sustained sections at 10 to 12 percent, which is common on forest tracks and old mule roads in the Alps, Pyrenees and Carpathians, calls for 0.65 or lower. Loose surface adds an effective 2 to 3 percent because the rear wheel slips. Altitude above 2,000 m takes 10 to 15 percent off available power, which in gearing terms means one extra sprocket.
Weight is the final variable, and it swamps everything. Going from 85 kg system weight to 105 kg with bags, water and a week of food increases the power needed on a climb by nearly a quarter. A rider who was happy on a 0.85 low gear unloaded will want 0.68 loaded to climb at the same cadence and effort. That is why the stock gearing on almost every gravel bike feels wrong the moment the bags go on.
What we would do to a stock bike
If the bike has a single ring above 38 teeth, fit a 32 or 34 and shorten the chain. If it has a double with a 30 inner, look for a 28 or 26 replacement ring and a cassette one step larger if the derailleur allows. If it has a triple, leave it alone. Then take the loaded bike to the steepest local hill and confirm you can climb it seated at 60 rpm. If you cannot, the gearing is still too tall, whatever the numbers say.
