Every bike-and-hike route we have ever planned has hit the same wall at some point: water. A lake that forces a 30 km detour, a river with no bridge for a day’s ride, a fjord whose far shore is visible and unreachable. For years the answer was to go round. Then packrafts became light enough to carry on a bike, and the wall turned into a shortcut. A packraft weighs 2 to 4 kg, rolls to the size of a sleeping bag, inflates with a bag in five minutes, and carries a bike lashed across its bow. It adds a third mode to the trip, and with it a whole new map.
What a bikeraft actually is
The idea is simple: ride to the water, take the wheels off the bike, strap the frame and wheels to the bow of an inflatable raft, paddle across or downstream, reassemble and ride on. The raft and paddle travel on the bike between water sections, usually on the handlebar or in a large seat pack. The bike travels on the raft during water sections, sitting on the tubes in front of the paddler where it is out of the way of the stroke. A four-piece paddle breaks down to about 60 cm and straps to the frame.
The weight penalty is real but modest. A raft, paddle, inflation bag, buoyancy aid and a few straps add 4 to 6 kg to a bikepacking load that already sits around 8 to 10 kg of bags. On the road that is noticeable on climbs and irrelevant on the flat. What changes more is the shape of the route, because the constraint of bridges and shorelines disappears.
Where water improves the route
The obvious use is a crossing. A lake 2 km wide takes twenty minutes to paddle and, if the far shore has a track, saves the road around it. Long thin lakes are even better used lengthways: Windermere in the English Lake District runs 17 km from end to end, and a calm morning paddle down it followed by a ride over the fells is a fine two-mode day. In the Scottish Highlands the Great Glen strings three lochs and a canal along 100 km between the west and east coasts, with a towpath and forest tracks for the bike and 37 km of Loch Ness for the raft, and the whole line can be done in three or four days by a party that knows when to switch.
The other use is the river descent. A gentle river flowing through a valley with a road on one bank makes a natural loop: ride upstream on the road, inflate, drift down for a few hours, ride back to camp. Rivers rated class I and II on the international scale, meaning moving water with small waves and few obstacles, are the packraft’s home ground, and a loaded bike on the bow makes anything harder unwise. We treat class III as the limit even for an unloaded raft and keep the bike well below that.
Lashing a bike to a raft
The bike goes on wheels-off, upside down or drive-side up depending on the raft’s shape, with the frame resting across the bow tubes and the wheels stacked on top or laid flat inside the bow. Three or four straps of about 1.5 m hold everything through the bow tie-downs, and we pull them tight enough that the bike cannot shift when the raft flexes on a wave. Pedals and chainrings get a quick wrap of an old inner tube to protect the fabric. The bags stay in their places on the frame or go inside the raft’s dry compartment if it has one.
The paddler needs to see over the load, so the bike sits as low as possible and the wheels do not stack higher than the bow. A test lash on the shore takes a few minutes and is worth doing before every crossing, because a bike that shifts on open water is a serious problem. Wind is the enemy on lakes: a bike on the bow acts as a sail, and a 25 km/h crosswind can push a small raft off its line faster than a paddler can correct.
- Wheels off, frame across the bow, wheels stacked low, three or four straps through the tie-downs.
- Protect the raft fabric from chainrings and pedals with an old tube or a rag.
- Bags stay sealed on the bike or go inside the raft; nothing loose.
- Test the lash on the shore and rock the raft before launching.
The transition is the crux
Switching modes costs time, and the bikeraft has two transitions per water section. Inflating, lashing and dressing for the water takes us fifteen to twenty minutes; the reverse takes ten, plus drying time if the raft is to be packed for a long ride. Four water sections in a day add two hours of fiddling. We plan for that and try to design routes with a small number of long water sections rather than many short ones.
Cold water is the safety issue that dominates everything else. A bike on the bow makes a capsize awkward, and even in summer a mountain lake sits at 10 to 15 degrees, which gives a swimmer minutes rather than hours. We paddle close to shore, wear a buoyancy aid always, dress for the water temperature rather than the air, and never paddle open water in a rising wind. Rivers add strainers, fallen trees that let water through but stop a boat, which are the single most dangerous feature on gentle rivers and the reason we scout any bend we cannot see round.
Is it worth the weight?
For a route with no water, no. For a route with one crossing that saves a day, or a river that turns a there-and-back into a loop, the raft pays for its 4 kg many times over. The trips where it has mattered most for us were never the spectacular descents; they were the ordinary lakes and estuaries that had always dictated the shape of the map. With the third mode in the bags, the map is drawn by us rather than by the bridges, and the moment of pushing off from a shore with the bike on the bow still feels like a small trick played on the landscape.
